View B43700_8342390.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

aluminum electrolytic capacitors capacitors with screw terminals series/type: B43700, b43720 date: november 2012 ? epcos ag 2012. reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without epcos' prior express consent is prohibited.
long-life grade capacitors applications frequency converters wind power converters solar inverters uninterruptible power supplies professional power supplies features high voltage 600 v dc high reliability and high ripple current capability all-welded constructions ensures reliable electrical contact papr terminals available (protection against polarity reversal) version with optimized construction for base cooling (heat sink mounting) available rohs-compatible construction charge-discharge proof, polar aluminum case with insulating sleeve poles with screw terminal connections mounting with ring clips, clamps or threaded stud the bases of types with threaded stud and d 76.9 mm are not insulated, types with d = 91 mm have fully insulated bases B43700 b43720 capacitors with screw terminals B43700, b43720 high voltage 600 v dc 85 c page 2 of 17 please read cautions and warnings and important notes at the end of this document.
1) refer to chapter "general technical information, 5 useful life" on how to interpret useful life. specifications and characteristics in brief rated voltage v r surge voltage v s 600 v dc 1.10 v r rated capacitance c r capacitance tolerance 1200 ... 6800 f 20% m dissipation factor tan d (20 c, 120 hz) 0.20 leakage current i leak (20 c, 5 min) self-inductance esl d 3 64.3 mm: approx. 20 nh useful life 1) requirements: 85 c; v r ; i ac,r > 6000 h d c/c 15% of initial value 40 c; v r ; 1.5 i ac,r > 75000 h tan d 1.75 times initial specified limit i leak initial specified limit voltage endurance test post test requirements: 85 c; v r 2000 h d c/c 10% of initial value tan d 1.3 times initial specified limit i leak initial specified limit vibration resistance test to iec 60068-2-6, test fc: frequency range 10 ... 55 hz, displacement amplitude 0.75 mm, acceleration max. 10 g , duration 3 2 h. capacitor mounted by its body which is rigidly clamped to the work surface. characteristics at low temperature max. impedance ratio at 100 hz v r 600 v z -25 c / z 20 c 3 z -40 c / z 20 c 10 iec climatic category to iec 60068-1: 40/085/56 ( 40 c/+85 c/56 days damp heat test) detail specification sectional specification similar to cecc 30301-803, cecc 30301-807 iec 60384-4 ripple current capability due to the ripple current capability of the contact elements, the following current upper limits must not be exceeded: capacitor diameter 64.3 mm 76.9 mm 91 mm i ac,max 45 a 57 a 80 a B43700, b43720 high voltage 600 v dc 85 c page 3 of 17 please read cautions and warnings and important notes at the end of this document.
dimensional drawings B43700 ring clip/clamp mounting b43720 threaded stud mounting the base of types with threaded stud and d = 91 mm is fully insulated (the lengths i and l 1 are in- creased by 0.5 mm in these cases). for types with threaded stud and d 76 mm the base is not insulated. also refer to the mounting instructions in chapter "capacitors with screw terminals accessories". screw terminals with unf threads are available upon request. dimensions and weights ter- minal dimensions (mm) with insulating sleeve approx. weight (g) d l 1 l 1 1 l 2 +0/ 1 d 1 d 2 max. a +0.2/ 0.4 m5 m5 m5 64.3 +0/ 0.8 64.3 +0/ 0.8 64.3 +0/ 0.8 105.7 118.2 130.7 112.2 124.7 137.2 17 17 17 m12 m12 m12 13.2 13.2 13.2 28.5 28.5 28.5 440 510 600 m6 m6 m6 m6 m6 m6 m6 76.9 +0/ 0.7 76.9 +0/ 0.7 76.9 +0/ 0.7 76.9 +0/ 0.7 76.9 +0/ 0.7 76.9 +0/ 0.7 76.9 +0/ 0.7 96.7 105.7 118.2 130.7 168.7 190.7 220.7 102.5 111.5 124.0 136.5 174.5 196.5 226.5 17 17 17 17 17 17 17 m12 m12 m12 m12 m12 m12 m12 17.7 17.7 17.7 17.7 17.7 17.7 17.7 31.7 31.7 31.7 31.7 31.7 31.7 31.7 570 620 700 800 1000 1150 1300 m6 m6 m6 m6 m6 91.0 +0/ 2 91.0 +0/ 2 91.0 +0/ 2 91.0 +0/ 2 91.0 +0/ 2 97.0 144.5 170.0 191.0 221.0 102.3 149.8 175.3 196.3 226.3 17 17 17 17 17 m12 m12 m12 m12 m12 17.7 17.7 17.7 17.7 17.7 31.7 31.7 31.7 31.7 31.7 770 1200 1400 1650 1900 B43700, b43720 high voltage 600 v dc 85 c page 4 of 17 please read cautions and warnings and important notes at the end of this document.
packing capacitor diameter d (mm) length l (mm) packing units (pcs.) 64.3 all 25 76.9 96.7 - 168.7 16 191.0 - 220.7 12 91.0 all 9 for ecological reasons the packing is pure cardboard. B43700, b43720 high voltage 600 v dc 85 c page 5 of 17 please read cautions and warnings and important notes at the end of this document.
special designs papr terminal style with our papr terminal style ( p rotection a gainst p olarity r eversal) we offer an optional mechanical feature in addition to the visual polarity marking on the cover disk and the sleeve, which prevents from mounting in reverse polarity. the non-circular shape of the terminals and their arrangement perpendicular to each other enables the user to definitely prevent wrong mounting with respect to polarity (poka yoke). dimensional drawing of papr terminal configuration dimensions for papr terminal style (mm) can diameter d terminal d 3 0.1 d 4 0.1 a +0.2/ 0.4 min. reach of screw standard design #050 for heat sink mounting #057 64.3 m5 13 15 28.5 9.5 7.3 76.9 m6 13 15 31.7 12.0 9.7 91.0 m6 13 15 31.7 12.0 9.7 all other dimensions of the capacitor such as diameter d, case length l and overall length l 1 are identical with those of standard capacitors of this series. please refer to the tables ?dimensions and weights? (standard types) and ?dimensions and weights for heat sink mounting? (special designs). for heat sink mounting design for optimal connection of capacitors to the heat sink when using base cooling with the following features (refer to chapter "general technical information, 5.2 cooling"): electrical insulation of the capacitors base with 2 overlapping thermal pads for optimal heat flow (minimal thermal resistance at the capacitor base) minimal overall length tolerance ( 0.35 mm) for mounting between heat sink and bus bar case with extra groove near the base for clamp mounting (recommended ring clamp b44030a0165b ... a0190b) B43700, b43720 high voltage 600 v dc 85 c page 6 of 17 please read cautions and warnings and important notes at the end of this document.
this version is available only for capacitors without threaded stud and for diameters 3 64.3 mm. regarding ripple current and useful life, please refer to column i ac,r (b) in the table "technical data and ordering codes" and in the useful life curves. dimensions and weights for heat sink mounting: ter- minal dimensions (mm) with insulating sleeve min. reach of screw mm approx. weight g d l 1 l 1 0.35 d 2 max. a +0.2/ 0.4 m5 64.3 +0/ 0.8 105.7 111.3 13.2 28.5 7.3 440 m6 m6 m6 m6 76.9 +0/ 0.7 76.9 +0/ 0.7 76.9 +0/ 0.7 76.9 +0/ 0.7 96.7 105.7 118.2 130.7 101.6 110.6 123.1 135.6 17.7 17.7 17.7 17.7 31.7 31.7 31.7 31.7 9.7 9.7 9.7 9.7 570 620 700 800 m6 m6 91.0 +0/ 2 91.0 +0/ 2 97.0 144.5 101.4 148.9 17.7 17.7 31.7 31.7 9.7 9.7 770 1200 dimensions for other sizes are available upon request. ordering codes: design identification in third block of ordering code remark for heat sink mounting m007 for capacitors without threaded stud papr terminal style m050 papr terminal style and heat sink mounting m057 for capacitors without threaded stud B43700, b43720 high voltage 600 v dc 85 c page 7 of 17 please read cautions and warnings and important notes at the end of this document.
accessories the following items are included in the delivery package, but are not fastened to the capacitors: thread toothed washers screws/nuts maximum torque for terminals m5 a 5.1 din 6797 din 7985 / iso 7045-m5 10-5.6-z 2.5 nm thread depth t 3 8 mm m6 a 6.4 din 6797 din 7985 / iso 7045-m6 12-5.6-z 4.0 nm thread depth t 3 9.5 mm for mounting m12 j 12.5 din 6797 hex nut bm 12 din 439 10 nm the following items must be ordered separately. for details, refer to chapter "capacitors with screw terminals accessories". item type ring clips b44030 clamps for capacitors with d 3 64.3 mm b44030 insulating parts b44020 B43700, b43720 high voltage 600 v dc 85 c page 8 of 17 please read cautions and warnings and important notes at the end of this document.
technical data and ordering codes c r 100 hz 20 c m f case dimensions d l mm esr typ 100 hz 20 c m w z max 10 khz 20 c m w i ac,max 100 hz 40 c a i ac,r 100 hz 85 c a i ac,r (b) 100 hz 85 c a ordering code (composition see below) composition of ordering code * = mounting style ## = design 0 = for capacitors with ring clip/clamp mounting 2 = for capacitors with threaded stud 00 = for capacitors with standard inductance 07 = for heat sink mounting (only capacitors without threaded stud) 50 = for terminals with papr style 57 = for terminals with papr style and heat sink mounting (only without threaded stud) v r = 600 v dc 1200 64.3 105.7 79 106 13.8 6.6 10.3 b437*0a8128m0## 1500 64.3 118.2 64 85 16.2 7.7 11.8 b437*0a8158m0## 1500 76.9 96.7 64 85 16.6 7.9 13.6 b437*0b8158m0## 1800 64.3 130.7 53 71 18.6 8.8 13.2 b437*0a8188m0## 1800 76.9 105.7 53 72 18.6 8.8 15.1 b437*0b8188m0## 2200 76.9 118.2 44 59 21.4 10.1 16.9 b437*0a8228m0## 2200 91.0 97.0 44 59 22.3 10.6 20.0 b437*0b8228m0## 2700 76.9 130.7 36 48 24.7 11.7 19.2 b437*0a8278m0## 3300 76.9 168.7 29 39 28.8 13.6 19.7 b437*0a8338m0## 3900 76.9 190.7 25 33 32.8 15.5 21.5 b437*0a8398m0## 3900 91.0 144.5 25 33 32.6 15.4 25.4 b437*0b8398m0## 4700 76.9 220.7 21 28 38.1 18.0 23.7 b437*0a8478m0## 4700 91.0 170.0 21 28 37.4 17.7 27.0 b437*0b8478m0## 5600 91.0 191.0 17 24 42.5 20.2 29.6 b437*0a8568m0## 6800 91.0 221.0 14 20 49.3 23.4 32.5 b437*0a8688m0## B43700, b43720 high voltage 600 v dc 85 c page 9 of 17 please read cautions and warnings and important notes at the end of this document.
1) refer to chapter "general technical information, 5 useful life" on how to interpret useful life. useful life 1) the useful life graph is calculated for each individual capacitor and is available upon request. frequency factor of permissible ripple current i ac versus frequency f frequency characteristics of esr typical behavior B43700, b43720 high voltage 600 v dc 85 c page 10 of 17 please read cautions and warnings and important notes at the end of this document.
impedance z versus frequency f typical behavior at 20 c B43700, b43720 high voltage 600 v dc 85 c page 11 of 17 please read cautions and warnings and important notes at the end of this document.
cautions and warnings personal safety the electrolytes used by epcos have been optimized both with a view to the intended application and with regard to health and environmental compatibility. they do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (dmf) or dimethyl acetamide (dmac). furthermore, some of the high-voltage electrolytes used by epcos are self-extinguishing. as far as possible, epcos does not use any dangerous chemicals or compounds to produce operating electrolytes. however, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no alternative materials are currently known. however, the amount of dangerous materials used in our products is limited to an absolute minimum. materials and chemicals used in epcos aluminum electrolytic capacitors are continuously adapted in compliance with the epcos corporate environmental policy and the latest eu regulations and guidelines such as rohs, reach/svhc, gadsl, and elv. mds (material data sheets) are available on the epcos website for all types listed in the data book. mds for customer specific capacitors are available upon request. msds (material safety data sheets) are available for all of our electrolytes upon request. nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: no electrolyte should come into contact with eyes or skin. if electrolyte does come into contact with the skin, wash the affected areas immediately with running water. if the eyes are affected, rinse them for 10 minutes with plenty of water. if symptoms persist, seek medical treatment. avoid inhaling electrolyte vapor or mists. workplaces and other affected areas should be well ventilated. clothing that has been contaminated by electrolyte must be changed and rinsed in water. B43700, b43720 high voltage 600 v dc 85 c page 12 of 17 please read cautions and warnings and important notes at the end of this document.
product safety the table below summarizes the safety instructions that must be observed without fail. a detailed description can be found in the relevant sections of chapter "general technical information". topic safety information reference chapter "general technical information" polarity make sure that polar capacitors are connected with the right polarity. 1 "basic construction of aluminum electrolytic capacitors" reverse voltage voltages polarity classes should be prevented by connecting a diode. 3.1.6 "reverse voltage" mounting position of screw- terminal capacitors do not mount the capacitor with the terminals (safety vent) upside down. 11.1. "mounting positions of capacitors with screw terminals" robustness of terminals the following maximum tightening torques must not be exceeded when connecting screw terminals: m5: 2.5 nm m6: 4.0 nm 11.3 "mounting torques" mounting of single-ended capacitors the internal structure of single-ended capacitors might be damaged if excessive force is applied to the lead wires. avoid any compressive, tensile or flexural stress. do not move the capacitor after soldering to pc board. do not pick up the pc board by the soldered capacitor. do not insert the capacitor on the pc board with a hole space different to the lead space specified. 11.4 "mounting considerations for single-ended capacitors" soldering do not exceed the specified time or temperature limits during soldering. 11.5 "soldering" soldering, cleaning agents do not allow halogenated hydrocarbons to come into contact with aluminum electrolytic capacitors. 11.6 "cleaning agents" upper category temperature do not exceed the upper category temperature. 7.2 "maximum permissible operating temperature" passive flammability avoid external energy, such as fire or electricity. 8.1 "passive flammability" B43700, b43720 high voltage 600 v dc 85 c page 13 of 17 please read cautions and warnings and important notes at the end of this document.
topic safety information reference chapter "general technical information" active flammability avoid overload of the capacitors. 8.2 "active flammability" maintenance make periodic inspections of the capacitors. before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. do not apply any mechanical stress to the capacitor terminals. 10 "maintenance" storage do not store capacitors at high temperatures or high humidity. capacitors should be stored at +5 to +35 c and a relative humidity of 75%. 7.3 storage conditions reference chapter "capacitors with screw terminals" breakdown strength of insulating sleeves do not damage the insulating sleeve, especially when ring clips are used for mounting. "screw terminals accessories" B43700, b43720 high voltage 600 v dc 85 c page 14 of 17 please read cautions and warnings and important notes at the end of this document.
symbols and terms symbol english german c capacitance kapazit?t c r rated capacitance nennkapazit?t c s series capacitance serienkapazit?t c s,t series capacitance at temperature t serienkapazit?t bei temperatur t c f capacitance at frequency f kapazit?t bei frequenz f d case diameter, nominal dimension geh?usedurchmesser, nennma? d max maximum case diameter maximaler geh?usedurchmesser esl self-inductance eigeninduktivit?t esr equivalent series resistance ersatzserienwiderstand esr f equivalent series resistance at frequency f ersatzserienwiderstand bei frequenz f esr t equivalent series resistance at temperature t ersatzserienwiderstand bei temperatur t f frequency frequenz i current strom i ac alternating current (ripple current) wechselstrom i ac,rms root-mean-square value of alternating current wechselstrom, effektivwert i ac,f ripple current at frequency f wechselstrom bei frequenz f i ac,max maximum permissible ripple current maximal zul?ssiger wechselstrom i ac,r rated ripple current nennwechselstrom i ac,r (b) rated ripple current for base cooling nennwechselstromstrom fr bodenkhlung i leak leakage current reststrom i leak,op operating leakage current betriebsreststrom l case length, nominal dimension geh?usel?nge, nennma? l max maximum case length (without terminals and mounting stud) maximale geh?usel?nge (ohne anschlsse und gewindebolzen) r resistance widerstand r ins insulation resistance isolationswiderstand r symm balancing resistance symmetrierwiderstand t temperature temperatur d t temperature difference temperaturdifferenz t a ambient temperature umgebungstemperatur t c case temperature geh?usetemperatur t b capacitor base temperature temperatur des becherbodens t time zeit d t period zeitraum t b service life (operating hours) brauchbarkeitsdauer (betriebszeit) B43700, b43720 high voltage 600 v dc 85 c page 15 of 17 please read cautions and warnings and important notes at the end of this document.
symbol english german v voltage spannung v f forming voltage formierspannung v op operating voltage betriebsspannung v r rated voltage, dc voltage nennspannung, gleichspannung v s surge voltage spitzenspannung x c capacitive reactance kapazitiver blindwiderstand x l inductive reactance induktiver blindwiderstand z impedance scheinwiderstand z t impedance at temperature t scheinwiderstand bei temperatur t tan d dissipation factor verlustfaktor l failure rate ausfallrate e 0 absolute permittivity elektrische feldkonstante e r relative permittivity dielektrizit?tszahl w angular velocity; 2 p f kreisfrequenz; 2 p f note all dimensions are given in mm. B43700, b43720 high voltage 600 v dc 85 c page 16 of 17 please read cautions and warnings and important notes at the end of this document.
the following applies to all products named in this publication: 1. some parts of this publication contain statements about the suitability of our products for certain areas of application . these statements are based on our knowledge of typical re- quirements that are often placed on our products in the areas of application concerned. we nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application . as a rule, epcos is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. for these reasons, it is always ultimately incum- bent on the customer to check and decide whether an epcos product with the properties de- scribed in the product specification is suitable for use in a particular customer application. 2. we also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified . in customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. the warnings, cautions and product-specific notes must be observed. 4. in order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . useful information on this will be found in our ma- terial data sheets on the internet (www.epcos.com/material). should you have any more de- tailed questions, please contact our sales offices. 5. we constantly strive to improve our products. consequently, the products described in this publication may change from time to time . the same is true of the corresponding product specifications. please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. we also reserve the right to discontinue production and delivery of products . consequently, we cannot guarantee that all products named in this publication will always be available. the aforementioned does not apply in the case of individual agreements deviating from the fore- going for customer-specific products. 6. unless otherwise agreed in individual contracts, all orders are subject to the current ver- sion of the "general terms of delivery for products and services in the electrical in- dustry" published by the german electrical and electronics industry association (zvei) . 7. the trade names epcos, baoke, alu-x, ceradiode, ceralink, csmp, cssp, ctvs, deltacap, digisimic, dssp, filtercap, formfit, miniblue, minicell, mkd, mkk, mlsc, motorcap, pcc, phasecap, phasecube, phasemod, phicap, siferrit, sifi, sikorel, silvercap, simdad, simic, simid, sineformer, siov, sip5d, sip5k, thermofuse, windcap are trademarks registered or pending in europe and in other countries. further information will be found on the internet at www.epcos.com/trademarks. important notes page 17 of 17

▲Up To Search▲

Price & Availability of B43700

	To Download B43700 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .